{"id":11773,"date":"2016-09-19T12:15:16","date_gmt":"2016-09-19T16:15:16","guid":{"rendered":"http:\/\/embedded-lab.com\/blog\/?p=11773"},"modified":"2016-10-01T21:52:50","modified_gmt":"2016-10-02T01:52:50","slug":"a-simple-diy-solar-powered-usb-charger","status":"publish","type":"post","link":"https:\/\/embedded-lab.com\/blog\/a-simple-diy-solar-powered-usb-charger\/","title":{"rendered":"A very simple DIY solar-powered USB charger"},"content":{"rendered":"

Yesterday, I built\u00a0a\u00a0very simple DIY solar-powered USB charger for my TP-link\u00a010400mAh<\/a> USB Power Bank.\u00a0All I needed was a 6V\/3.5W solar panel<\/a><\/strong> and the TD1410-based 5V buck converter module<\/a><\/strong>. I bought both of them on Aliexpress for less than $8.<\/p>\n

\"charger1\"<\/a>

Simplest DIY solar-powered USB charger<\/p><\/div>\n

It was one of the easiest projects I\u00a0built. All I\u00a0needed to do was to connect\u00a0the input of the 5V step-down buck converter to the output of the solar panel using\u00a0two wires.<\/p>\n

\"charger3\"<\/a>

Connections between the 5V buck converter and solar panel<\/p><\/div>\n

From TD1410 datasheet,<\/p>\n

The TD1410 is a 380 KHz fixed frequency monolithic step down switch mode regulator with a built in internal Power MOSFET. It achieves 2A continuous output current over a wide input supply range with excellent load and line regulation. The device includes a voltage reference, oscillation circuit, error amplifier, internal PMOS and etc.<\/p><\/blockquote>\n

For 5V output from TD1410, the input voltage can range from 5.5V to 20V (from the datasheet). I measured the solar panel open-circuit voltage under sunny conditions to be ~ 6.5V. Under the load of 200 mA, the solar panel output voltage was reduced to ~6.0V. The TD1410-based 5V buck converter\u00a0module that I purchased on Aliexpress already has a diode at its input for polarity protection. So I didn’t need\u00a0any extra diode for the solar panel output as it directly goes to the input of the buck converter. The nice thing about this buck converter is it has a USB-A female port for output, which is same as found in standard USB chargers. It also comes with a plastic enclosure (see pictures below).<\/p>\n

\"Buck<\/a>

Buck converter with a plastic enclosure and screws<\/p><\/div>\n

\"Close<\/a>

Close up view of TD1410-based 5V buck converter<\/p><\/div>\n

The positive and negative outputs from the solar panel connects to the +<\/strong> and –<\/strong> inputs of the buck converter, respectively. I put the buck converter inside the enclosure and glued it on the back of the solar panel as shown below.<\/p>\n

\"5V<\/a>

5V converter module glued to the backside of the solar panel<\/p><\/div>\n

The USB output voltage from the buck converter was measured to be 5.05V using my TENMA multimeter. I could even charge a\u00a0Xiaomi Redmi Note 2 smartphone directly from the USB port under full sun<\/strong> conditions. I measured the charging current was ~200 mA.\u00a0If the sky is partly cloudy, the solar panel might not supply the adequate current for charging the smartphone directly (of course, it also depends upon the smartphone). In the absence of enough input current, the smartphone’s built-in charging circuitry will refuse to go in to the charging mode. If there’s a fluctuation in the incident solar irradiation due to varying cloud condition, it is likely that the smartphone will go back and forth between charging and not charging. So, I would not recommend it for direct charging of\u00a0smartphones. But it is safe for charging the USB power banks as they can be charged at a lower current input.<\/p>\n

\"charger2\"<\/a>

Direct charging of smartphone (at 200 mA) using the solar power. Charging is interrupted under partly cloudy conditions.<\/p><\/div>\n

\"s\"<\/a>

Portable DIY solar charger<\/p><\/div>\n

In conclusion, this solar-powered USB charger was super simple to build, very portable to carry around and works perfectly for charging USB power banks. Two or more of these solar panels can be connected in parallel to achieve a higher current output.<\/p>\n","protected":false},"excerpt":{"rendered":"

Yesterday, I built\u00a0a\u00a0very simple DIY solar-powered USB charger for my TP-link\u00a010400mAh USB Power Bank.\u00a0All I needed was a 6V\/3.5W solar panel and the TD1410-based 5V buck converter module. I bought both of them on Aliexpress for less than $8. It was one of the easiest projects I\u00a0built. All I\u00a0needed to do was to connect\u00a0the input of the 5V step-down buck converter to the output of the solar panel using\u00a0two wires. From TD1410 datasheet, The TD1410 is a 380 KHz fixed frequency monolithic step down switch mode regulator with a built in internal Power MOSFET. It achieves 2A continuous output current<\/p>\n","protected":false},"author":1,"featured_media":11891,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[245,1464,30,1467,1450],"tags":[1449,891],"class_list":["post-11773","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-embedded-lab-projects","category-featured","category-power-supply","category-projects","category-solar-power","tag-diy-solar-powered-usb-charger","tag-voltage-regulator"],"_links":{"self":[{"href":"https:\/\/embedded-lab.com\/blog\/wp-json\/wp\/v2\/posts\/11773","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/embedded-lab.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/embedded-lab.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/embedded-lab.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/embedded-lab.com\/blog\/wp-json\/wp\/v2\/comments?post=11773"}],"version-history":[{"count":10,"href":"https:\/\/embedded-lab.com\/blog\/wp-json\/wp\/v2\/posts\/11773\/revisions"}],"predecessor-version":[{"id":11791,"href":"https:\/\/embedded-lab.com\/blog\/wp-json\/wp\/v2\/posts\/11773\/revisions\/11791"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/embedded-lab.com\/blog\/wp-json\/wp\/v2\/media\/11891"}],"wp:attachment":[{"href":"https:\/\/embedded-lab.com\/blog\/wp-json\/wp\/v2\/media?parent=11773"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/embedded-lab.com\/blog\/wp-json\/wp\/v2\/categories?post=11773"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/embedded-lab.com\/blog\/wp-json\/wp\/v2\/tags?post=11773"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}