{"id":7336,"date":"2013-04-20T15:54:03","date_gmt":"2013-04-20T19:54:03","guid":{"rendered":"http:\/\/embedded-lab.com\/blog\/?p=7336"},"modified":"2023-07-13T14:45:04","modified_gmt":"2023-07-13T18:45:04","slug":"easy-pulse-version-1-1-sensor-overview-part-1","status":"publish","type":"post","link":"https:\/\/embedded-lab.com\/blog\/easy-pulse-version-1-1-sensor-overview-part-1\/","title":{"rendered":"Easy Pulse Sensor (Version 1.1) Overview (Part 1)"},"content":{"rendered":"

The Easy Pulse sensor is designed for hobby and educational applications to illustrate the principle of photoplethysmography (PPG) as a non-invasive optical technique for\u00a0detecting cardio-vascular pulse wave from a fingertip. It uses an infrared light source to illuminate the finger on one side, and a photodetector placed on the other side measures the small variations in the transmitted light intensity. The variations in the photodetector signal are related to changes in blood volume inside the tissue. The signal is filtered and amplified to obtain a nice and clean PPG waveform, which is synchronous with the heart beat. The original version of Easy Pulse<\/a><\/strong>\u00a0uses the TCRT1000 reflective optical sensor to sense the blood variation in the finger tissue and outputs a digital pulse which is synchronous with the heart beat. Today, we are pleased to announce the release of Easy Pulse Version 1.1, which has some improvements over the original design. The new version provides both analog PPG waveform as well as digital pulse signal as separate outputs. Easy Pulse Version 1.1 board is available for purchase on Tindie<\/a><\/strong>. Recently, our Chinese distributor Elecrow<\/a><\/strong> has also started selling it for $18.50, and they can ship it world-wide at lower cost.<\/p>\n

\"\"<\/a>

Easy Pulse version 1.1<\/p><\/div>\n


\nQuick overview of Easy Pulse<\/strong><\/p>\n

The Easy Pulse sensor is based on the principle of photoplethysmography (PPG) which is a non-invasive method of measuring the variation in blood volume in tissues using a light source and a detector. Since the change in blood volume is synchronous to the heart beat, this technique can be used to calculate the heart rate.\u00a0Transmittance and reflectance are two basic types of photoplethysmography.\u00a0For the\u00a0transmittance PPG, a light source is emitted in to the\u00a0tissue and a light detector is placed in the opposite side of the\u00a0tissue to measure the resultant light. Because of the limited penetration depth of the light through organ tissue, the transmittance PPG\u00a0is applicable to a restricted body part, such as the finger\u00a0or the ear lobe. However, in\u00a0the reflectance PPG, the light\u00a0source and the light detector are both placed on the same side of a\u00a0body part. The light is emitted into the tissue and the reflected light is measured by the detector. As the light doesn\u2019t have to penetrate the body, the reflectance PPG can be applied to any parts of human body. In either case, the\u00a0detected light reflected from or transmitted through the body part will fluctuate according to the pulsatile blood flow caused by the beating of the heart.<\/p>\n

The original Easy Pulse<\/a><\/strong> design was based on the reflectance approach and used TCRT1000 IR device as sensor. It could detect the pulse signal when an user places his\/her fingertip on the top of the sensor. While this sensor performed well, it was susceptible to a very small movement of the finger. So, the user should keep the finger very steady to obtain the accurate pulse signal. Easy Pulse Version 1.1 uses a more robust sensor (HRM-2155E) that operates in transmission mode and fits tight around the fingertip, thereby it is less prone to motion.<\/p>\n

The HRM-2511E sensor is manufactured by Kyoto Electronic Co., China, and operates in transmission mode. The sensor body is built with flexible Silicone rubber material that helps to keep the sensor tightly hold to the finger. Inside the sensor case, an IR LED and a photodetector are placed on two opposite sides and are facing each other. When a fingertip is plugged into the sensor, it is illuminated by the IR light coming from the LED. The\u00a0photodetector diode receives the transmitted light through the tissue on other side.\u00a0More or less light is transmitted depending on the tissue blood volume. Consequently, the transmitted light intensity varies with the pulsing of the blood with heart beat. A plot for this variation against time is referred to be a photoplethysmographic or PPG signal.\u00a0The following picture shows a basic transmittance PPG probe setup to extract the pulse signal from the fingertip.<\/span><\/p>\n

\"\"<\/a>

HRM-2511E as a transmission PPG probe<\/p><\/div>\n

The PPG signal consists of a large DC component, which is attributed to the total blood volume of the examined tissue, and a pulsatile (AC) component, which is synchronous to the pumping action of the heart. The AC component, which carries vital information including the heart rate, is much smaller in magnitude than the DC component.\u00a0A typical PPG waveform is shown in the figure below (not to scale).<\/p>\n

\"\"<\/a>

PPG components shown not to scale<\/p><\/div>\n

The two maxima observed in the PPG are called Sytolic and Diastolic peaks, and they can provide valuable information about the cardiovascular system (this topic is outside the scope of this article). The time duration between two consecutive Systolic peaks gives the instantaneous heart rate.<\/p>\n

Here are the features of Easy Pulse V1.1 sensor module.<\/p>\n